- Noodle/Boot completely seal brake cable, upgrades most linear brakes
- Includes stainless bolts - Fits 160mm front and 140mm rear rotors
- Includes stainless steel bolts - 40mm fits 200mm Front and 180mm Rear Rotors
$44.99 - $55.66
- Fits 2000 and newer Campagnolo wheels - Fits all Fulcrum wheels - Fits 1999 Record/Chorus hubs and all Campy hubs 2000-newer - 27.0mm thread OD 10-speed: - For use with Campagnolo cassettes with 12 to 16 tooth first position cogs - Lockring has a 38.5mm flange diameter 11-speed: - For use only with Campagnolo 11 speed cassettes with 12 tooth first position cogs
- Asymmetrical design with an offset slot specifically for carbon seatposts - Fitment based upon seattube sizes: 34.9-35.2 For 31.6 Posts. - 24g
Allows the lower of a 47mm IS headtube to be converted to use a standard 41mm 36x45 degree headset bearing.
Hellbender bearings have an improved seal structure and are cross compatible with Cane Creek headsets.
All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 17mm - Outer Diameter: 28mm - Width: 7mm
$9.99 $15.99 38% Off
- Specially shaped composite material helps prevent chain derailment when shifting to inner ring - Split clamp design mounts to specific seat tube diameters, eliminating the need for a metal fitment clamp
Dimension Seatpost Clamps - Diameters: 28.6mm, 30.0mm, 31.8mm, 35.0mm - Weight: 34g
$26.99 $29.99 10% Off
Dimension Stem Column Adaptors - Total quill length 180mm - Measurement from minimum insertion to top of steerer adaptor is 118mm - Alloy - Quill insertion diameter: 1-inch
Dimension Steerer Extender adds 2 to 3-1/4" height to steerer. - Extender clamps to steerer; stem clamps to extender - Adds 2 to 3-1/4-inch height to threadless steerer - Includes top cap and long bolt - 40mm of threadless steerer is required for proper installation - Do not stack steerer extenders; no more than one steerer extender recommended per bike - WARNING: Dimension Steerer Extender is not recommended for use on forks with carbon fiber steerers
What It Is Replacement hardware for ENVE carbon fiber seatposts. Who It's For Folks who need additional hardware for their ENVE seatposts. Why We Made It We get calls all the time for replacement hardware, so we made a little kit to make it easy for everyone.
- Microspacers ensure the correct fitment of integrated headsets - Use between the top cover and the compression ring to ensure the top cover does not contact the headtube - Sold in bags of 10
It seems so small and insignificant, yet it's so important. The BB30 Wave Spring Washer is the keystone in your bottom bracket assembly, providing compression for proper setup and bearing preload, while helping to maintain adjustment after it's dialed in just right. They're also quite easy to lose or damage, so grab a few while you're at it.
Stainless steel pedal washers - Sold in pairs
Your frame is BB30 or PF30. Your crank is 386EVO. No sweat. This adapter from FSA makes it happen. - For road use - Weight: 50g
This is an FSA MegaExo Crank Arm Fixing Bolt for MegaExo Cranks. - 26mm length - 12g - Designed to fit FSA cranks only - Includes M18 bolt, M27 self-extracting cap and washers
Keep that front end tight and responsive, while preserving the integrity of the carbon steerer on your high-end fork with FSA's Headset Compression Plug. - Alloy top cap - For carbon steer tubes
Transfer Dropper Post Remote A lightweight below-the-bar design for 1x drivetrains. FOX Transfer post levers provide smooth action and reduced force, providing consistent actuation pressure to raise or lower the seat. - 22.2 1x Remote I-Spec EV
$4.49 - $44.99
Jagwire's Brake or Shift Cable Tips are made of lightweight, corrosion-resistant and durable aluminum and are the right size to nicely fit over the ends of up to 1.8mm-diameter cables. These caps are crimped in place on the cables to prevent fraying and ensure your cables last a long time. The tips come in colors to add a little style to your bike.
Inline adjusters make on-the-fly derailleur cable tension adjustments safe and easy. - Indexed shifter adjustment, fits 4.0mm housing; not recommended for use with brake systems - Compact design improves performance when used on curved housing segments
Use these stainless steel Jagwire disc brake shims to position a 6-bolt rotor in just the right spot.
$30.99 - $61.99
Sport brake housing packs high performance features into a colorful and durable package, making it a functional and aesthetic upgrade. - Slick-Lube lined housing reduces friction for faster cable movement and better braking response - High carbon internal steel coil for improved stiffness - Appropriate for Teflon coated cables as well as steel and galvanized
$59.99 - $64.99
Pro Compressionless brake housing eliminates flex from cable actuated braking systems, increasing power and improving lever feel. - KEB-SL - linear strand, Kevlar reinforced, compressionless brake housing with Slick-Lube liner - Perfect for full-housing, high-performance bikes with mechanical disc or rim brakes - 20 black alloy lined end caps, 10 black POP end caps included
The Pro Braze-On Chain Catcher from K-EDGE is used by most professional cyclists and pro teams around the world, in all types of racing including prestigious Olympic Games, World Championships, and Grand Tours, such as the Tour de France, Paris-Roubaix, and Giro d ’Italia. The Pro model is designed to improve on the original K-EDGE Chain Catcher design: - Easier Installation – Independent setup and installation of front derailleur and the K-EDGE Chain Catcher - Stronger – Separate and lower attachment /adjustment bolt equates to stronger hold ensuring the chain cannot drop below the chain catcher - Optimized Design – Unique curved ramp profile enables quicker chain engagement with the chain ring while eliminating dropped chains - Material: 6061-T6 CNC machined Aluminum - Fitment: All braze-on mounted front derailleurs* - Hardware: Includes all mounting hardware for Shimano, SRAM, and Campagnolo front derailleurs * Not compatible with Campy EPS * May not work with all third-party braze-on adapter clamp. Shimano - Made in Boise, Idaho, USA, - Lifetime Guarantee against material or manufacture defects. Damages due to abuse or crashing excluded.
$1.99 - $4.99
- Half-link connector allows you to add or subtract half of one link (1/2 inch) from the chain in order to optimize chain tension - Uses standard chain pin connector and tool
- Underbar dropper remote, ideal for bikes with 1x drivetrain - Split clamp allows 4-axis of adjustment for perfect setup - Upgrades all remote Kind Shocks (not intended for lever adjustable models and not compatible with first generation LEV Integra)
The new G4 picks up where the famous G3 left off — three consecutive appearances in the Dirt 100 issue, as well as countless World Cup and FMB podiums made it the most sought after full-featured guide on the market. Upgrades to the G4 include a new co-molded upper guide that utilizes a softer durometer TPU material on the interior walls and ceiling to silence drivetrain chatter. An improved material formula is utilized in the updated skid — making the best even better. - Full-size, nylon upper guide with co-molded TPU material on the interior walls and ceiling that silences chain contact. - Integrated skid protects chainrings and glides over rocks and obstacles. - Includes standard pulley and G-slide slider block for quiet, dependable operation in muddy and dank conditions. - Compatible with chainlines 50mm and wider (55mm and wider on 83mm BB shells) - 204g (Mega Alloy ISCG)
- Lower cables for Odyssey's Gyro G3 (sold separately). - Universal fit. - Lower cables only.
- Upper cables for Odyssey's Gyro G3 (sold separately) - Universal fit. - Upper cables only.
$3.99 - $20.00
Available in the most common sizes and thicknesses-in small or bulk quantities, Problem Solvers headset spacers help riders get their stack height just right. - Made from Aluminum, anodized or polished finish, without logos - 1-1/8" Diameter - S.H.I.S. Stem Clamp Diameter: 28.6mm
$3.99 - $5.15
The Problem Solvers Brake Boss Plugs are perfect for when you've removed your cantilever or linear-pull brakes in order to run disc brakes or a fixie setup. These plugs thread into the empty frame bosses and lend a clean look, while also protecting the threads inside the frame from corrosion.
Problem Solvers' 11-speed Freehub Spacer converts your 11-speed freehub body to accept a 10-speed casssette. Use this spacer if you are running a 10-speed drivetrain on a new set of wheels with a 11-speed freehub body. The spacer is 1.85mmm thick.
$5.99 - $6.99
The Problem Solvers Steerer Tube Shims are for installing 1-1/8-inch diameter threadless stems on 1-inch diameter threadless forks. The shim is made of light, durable anodized aluminum and is chamfered on the ends for easy stem installation.
$6.99 - $7.15
The Problem Solvers Cantilever Studs screw into the bosses built into bicycle frames to provide the proper mounting studs for brakes. Each brake requires two studs.
The Problem Solvers Cassette Spacers are made of light and durable anodized aluminum and come in different thicknesses for correctly spacing various brand and model cassette cogs. Measure and match your spacers to choose the right width.
$8.99 - $12.99
The Problem Solvers Clamp-On Cable Hanger is made of light, durable anodized aluminum and fits on bicycles with 1- and 1 1/8-inch forks. A cable noodle and guide are included.
Replace old brake barrel adjusters with a fresh pair of Problem Solvers' 10mm Brake Barrel Adjuster. Designed for use with standard brake cables.
$9.99 - $12.99
The Problem Solvers Handlebar Clamp Shim allows you to fit almost any handlebars in almost any stem. It's machined of light and durable aluminum and grooved on the inside to hold tightly.
$9.99 - $11.99 $11.99 - $14.99 Up to 33% Off
Problem Solvers has a couple different options for adding cable housing or brake hose guides to your bike. Choose from the adhesive stick-on option or the guide that mounts to existing housing stops.
Notched binder bolts for frames with integrated seat collars. Details: CroMoly steel bolts Three lengths available: 16, 19 and 21mm 8mm diameter
$9.99 - $15.90
The Problem Solvers Seatpost Shim is what you need when your seatpost is a little too small-diameter to fit tightly into your frame. It's made of light, durable aluminum and has a lip on the top so it won't slide down inside the frame during installation.
Switching frames doesn’t mean you have to switch posts! Use your old posts without worry with Problem Solver's wide variety of seatpost shims. -100mm long -3mm lip -Alloy Problem Solvers Seatpost Shims are not intended for use with carbon seatposts
$10.99 - $15.15
The Problem Solvers Standard Top Cap is a light, durable aluminum top cap for threadless headsets. These caps fit all forks.
$11.99 - $44.99 $29.99 - $44.99 Up to 60% Off
Problem Solvers' MisMatch Adapters allow you to combine your Shimano and SRAM shifters and brakes onto a single clamp for a more ergonomic, less-cluttered handlebar. These CNC-machined aluminum adapters work with Shimano I-Spec and SRAM MatchMaker components to fasten your preferred combination on to a single, existing bar clamp.
$12.99 - $13.15
The Problem Solvers Brake Mounting Nut is for front caliper brakes that take recessed fixing nuts. This chrome-plated steel Allen nut comes in 2 long lengths so that it will grip enough threads to tightly fasten the brake on even the thickest of fork crowns.
$13.99 - $21.99
The Problem Solvers Cross Hanger is the perfect front brake cable hanger for your cyclocross bike with cantilever brakes. Designed for easy installation and maximum braking power, this light, durable aluminum piece is a small but crucial part of your cantilever setup.
$14.15 - $23.50
The Problem Solvers Double Chainring Bolts include 5 chainring bolts and nuts that are 8mm wide. This is the right size for most double-chainring setups. These chainring bolts are made of either aluminum, stainless steel, or chromoly.
$14.99 - $24.99
Problem Solvers' Cassette Cog Carrier (CCC) bolts on to a splineless single-speed cog to give you a wide, Shimano-splined cog to run on your freehub body. The wide profile won't damage your freehub body. Tech Details: Aluminum carrier with steel cogs
$15.99 - $23.50
The Problem Solvers Single Chainring Bolts include 5 chainring bolts and nuts that are 6mm wide. This is the right size for most single-chainring setups. These chainring bolts are made of either aluminum, stainless steel, or chromoly.
$17.99 - $20.99
The Problem Solvers Braze-On Front Derailleur Adapter simply clamps onto your frame's seat tube and provides a secure place to bolt on your braze-on front derailleur (sold separately). This fine adapter is made of light, durable aluminum and includes a stainless-steel bolt.
The Problem Solvers Universal Derailleur Hanger is a handy thing to keep on hand (and even bring on epic off-road rides or extended tours) because it makes it relatively easy to fix a damaged/bent derailleur hanger, which is a pretty common breakdown. This CNC-machined 6061-aluminum hanger takes the place of the drive-side quick-release nut providing a straight hanger to mount your derailleur to. You'll still be able to shift into many of your gears, too.
The Problem Solvers Self-Extracting Crank Bolts take the place of the existing bolts in Shimano/Octalink, Race Face ISIS, and M15-compatible cranksets to let you remove your crankarms with only an 8mm Allen wrench instead of special tools. A 10mm Allen wrench (sold separately) is used to install these fine aluminum self-extractors.
The Problem Solvers Backstop bolts onto the frame to provide two stops for your cable housing. It's made of light, durable CNC-machined aluminum with a stainless-steel bolt, and the stops are slotted for easy cable installation/removal.
$24.99 - $44.99
MisMatch adapters allow users to mount Shimano & SRAM brakes and shifters on one clamp. MisMatch Adapter 1.0/1.1 attaches SRAM shifters to Shimano I-Spec-A or I-Spec-B brake lever clamps. MisMatch adapters and the ever evolving “standards” it attempts to integrate between SRAM and Shimano is a confusing subject. Shimano brake and shifter mounting options have changed a lot, going through four mounting systems from 2011-2016. Shimano components have a model number printed somewhere on the brake and/or shifter, and this is the best way to determine what you own and what adapter you need. MisMatch 1.0/1.1 fits Shimano brake levers:BL-M985, BL-M988, BL-M820, BL-M785, BL-T785, BL-M675, BL-T675, BL-M640, BL-M596, BL-M820-B, BL-M785-B, BL-M675-B, BL-M640-B, BL-M615, BL-M506 - Annodized Black
$25.65 - $57.20
The Problem Solvers Head Tube Reducers resize your head tube to accommodate different size forks. These fine aluminum reducers are designed for traditional, external-cup headsets. Please contact us for any questions about compatibility with your bicycle.
The Problem Solvers Direct Mount Adapter gives you a place to install direct-mount Shimano and SRAM derailleurs. It was initially developed for standard mountain bike frames with 68/73mm wide bottom bracket shells, and is equally suited to fat/snow bikes, where their 100mm wide bottom brackets make front derailleur applications a little difficult. The adapter is made of light and durable 6061 aluminum.
MisMatch adaptors allow users to mount Shimano & SRAM brakes and shifters on one clamp. Available in multiple configurations. -Annodized Black -Attaches SRAM shifters to Shimano I-Spec II brake lever clamps MisMatch 1.2 adaptor fits Shimano brakes: BL-M9020, BL-M9000, BL-M8000, BL-M7000
• Allows the use of downtube shifters on bikes without downtube shifter braze-ons • Compatible with 9/10-speed Shimano shifters • 31.8mm clamp with shims for 28.6mm tubes • Shifters not included
Page 1 of 3 Next page